Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Upgrade Kit
Includes our new 2024 control unit with:
Reverse on the fly.
Thermal overload protection.
Software based jam protection.
Adjustable brake.
Adjustable soft start.
Power outage protection. (Will not restart while you are away)
Emergency E_Stop (adjustable between coast and immediate)
10 RPM speed increments. (the competition is 100 RPM increments)
See Image 1 for what is in the box.All other images are for information only.
Fits Many Mini Metal Lathes.
Sold complete with all the adapters required to install in the original motor location of your spindle drive mini metal lathe.
Allows for complete reinstall of all threading gears and auto feed systems.
Fits mini metal lathes that the drive belt goes directly to the spindle gear.
Does not fit mini metal lathes that have an intermediate shaft (high/low gear). To fit these you would need to purchase one of my systems designed for two speeds. See our Mini Metal Lathe 1 hp Servo Motor 2 speed kit
The horsepower improvement is incredible.
Kinda like replacing the small block with a big block in your Mustang/Camaro muscle car. Just pure power, so much so that you will never use all of it.
This system provides full power at any speed and that includes Spindle RPM's as low as 200 RPM's
Motor and spindle speeds + Reverse:
The motor speed can be programmed and or full range can be achieved with just the speed control knob:
Speed control programming only requires a few easy steps.
Reverse is simple, just hold the yellow button for a few seconds.
Programming includes the ability to set bottom and top RPM range separately. In other words you can program the system to run the spindle at any speed or range of speeds you choose (see below).
Slowest speed achievable: Motor 100 RPM = Spindle 60 RPM.
Highest speed this one produced: Motor 3,500 RPM = Spindle just over 2,000 RPM's.
Note: it is not recommended to spin the spindle any faster unless you upgrade the factory installed spindle bearings.
Motor Specifications:
Watt: 750 (1.0057665666 HP)
Voltage: 110V
HZ: 60
Torque: 10 N.M.
RPM: 200 to 4,500 RPM in 10 RPM increments.
Note: Manufacturer recommended 500 to 4,000 RPMs
My personal testing results: This motor runs best between 300 and 4,500 RPMs.
Ratio of belt drive:
1.6 to 1 (motor turns 1.6 revolutions to every revolution the spindle turns)

Mini Metal Lathe 750 Watt Servo Motor Upgrade Kit. Spindle Drive

Name: Mini Metal Lathe 750 Watt Servo Motor Upgrade Kit. Spindle Drive
SKU: 000001

SKU: 000001

$310.00

Excluding Sales Tax

Quantity

A new 750 watt motor like the one seen here in photos above and on you-tube. Motor will come with the motor mount installed. This will require adjustment to fit your lathe. It will also come with the small timing pulley installed on it using a 5 mm key-way and main shaft nut.

A new 2024 control computer like the one seen in the above photos. This control unit is built by The Custom Crafter to include:
A. Built in Thermal overload protection rocker style switch with reset function. See photos, make note of the orange power switch with the word RESET. If your switch is red or if it does not say reset, it does not have thermal overload protection.
B. Software based jam protection.
C. Internal speed control rotary switch.
D. Reverse on the fly function.
E. Power went out safty circuit.

The Custom Crafter made in the USA motor mount. (installed on motor, see line 1). Includes thick washers and grade 8 nuts.

The Custom Crafter made in USA spindle bearing head adapter (see photos).

The Custom Crafter made in USA spindle spacer (see photos).

One custom made anodized and polished aluminum spindle timing pulley. (see photos).

One custom made anodized polished aluminum motor timing pulley. (see photos). Comes preinstalled on motor (see line 1).

A new L050 1/2" wide timing belt.

On-line access to interactive programming instructions and fault codes. Written in plain English by us.. Includes recommended programming settings and fault codes.

The Custom Crafter quick program and spindle speed card.

Package will not include written assembly instructions.

A text number for direct assistance from the custom Crafter.
Assembly requires some technical skill to include minor machine work.
Note: Check the photos in this listing. See the red lathe. If your lathe has holes instead of the normal slots, this motor will not fit without your ability to slot the cast iron lathe bed. Additionally if you return this item for this reason, you will pay shipping both ways.

You will have to cut the die-cast gear housing to allow additional room for the larger timing belt. (see photos)
this can be done with a hacksaw and a file but a pneumatic cut off tool or die grinder will ease this job.

A spreader wrench is a big help but this can be managed with a hammer and punch.

You will need metric and domestic allen wrenches + a 13mm/1/2" deep socket and ratchet.

Some longer allen head metric allen head bolts (not included) may also be required, especially it you over tighten and strip the factory bolts provided with your machine.
If you have a mini lathe this is the best upgrade for the money by far.

Great Kit A+.

I love it great product and support.

Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit Fits Original Location Gear.

Awesome product, crazy power output, thanks!

took me about an hour to install I still have to make a mount for the controller. what a amazing enhancement to my lathe. Dan is a stand-up man, he had it shipped out to me ASAP I had it in 3 days. the power is incredible. thank you very much for your time invested with developing a product for a very fair price that is an amazing enhancement.
Items costing less than $15 each are not returnable.

No reason is required.

Buyer pays shipping both ways.

Buyer provides tracking number that shows the item is in possession of the return shipping company before the 30 day time period runs out.

30 day time period starts when tracking shows original order as in possession of USPS.

Buyer to provide tracking # and shipping company name to be e mailed to servomotorkit@gmail.com within 36 hours of when issued.

Return must be shipped through USPS, UPS or FedEx.

All items returned must be in like new and unused condition:
This includes original packaging.

Missing packaging will result in a restocking charge of up to 20%

Installed items will not be refunded or charged up to 50% to restore and resell as a refurbished unit
Limited 180 day parts warranty. Labor is buyers responsibility:
See details, what's covered and for how long etc below. Shipping both ways for all parts returned for warranty is the buyers responsibility. Parts returned will be inspected for unique identification mark and or abuse. If found to be abuse or missing the identity mark, no warranty exchange part will be provided and buyer will be required to pay shipping to get their parts back. Warranty exchange parts may or may not be new but instead refurbished or demos that I have from previous builds. Warranty starts on the day our records show the system as paid and not the date the item is actually received.

Servo Motor. - I will exchange a defective servo motor for up to 180 days. Buyer must return the motor + the control unit + the speed control switch for inspection and testing. Additionally original packaging such as Styrofoam package inserts must be used to return these parts.

Computer control unit. - I will exchange a defective control unit PCB for up to 180 days. Buyer must return the motor + the control unit + the speed control switch for inspection and testing. Additionally original packaging such as Styrofoam package inserts must be used to return these parts.

Improper instalation or abusive operation is not warrenty.
Print and keep your receipt, it could save you money.. We keep all parts in stock. That means if you brake it, we can fix it within days, not months to years waiting for parts from the large US sellers. Honesty goes a long way. If you smoked it just say so.
We will ask a few questions and then sell you the correct replacement parts. Optionally we will ask you to return the control unit for repair and repair it for you at $45 plus shipping.

Mini Metal Lathe 750 Watt Servo Motor Upgrade Kit. Spindle Drive

System Includes

Assembly

Recent Feedback:

Shipping:

Basic 30 day return policy:

180 Day Warranty:

Up to one year extended customer support:

How can we help?